Component Spotlights· 9 min read
MT52L256M32D1PF-107 WT:B

MT52L256M32D1PF-107 WT:B: Micron 8Gb LPDDR3 Specs and End-of-Life Guide

Micron's MT52L256M32D1PF-107 WT:B is an 8Gb x32 LPDDR3 part past its August 2026 last order date: specs, known platforms and what a replacement must match.

By Ryan Munoz
Isometric illustration of a microscope objective positioned above the solder balls on the underside of a memory chip.

The MT52L256M32D1PF-107 WT:B is an 8Gb Micron LPDDR3 memory device, organized as 256 Meg x 32 on a single die in a 178-ball FBGA. It is end of life. Micron’s end-of-life notice set a last order date of 2026-08-31 and a last ship date of 2027-09-01, and franchised distributors now list the part as obsolete.

If a product you build still uses it, you need to know three things: how long you can keep buying it, what a replacement would have to match and how to check obsolete stock before it reaches your line.

Memory category illustration

In stock at NetSource

MT52L256M32D1PF-107 WT:B

MICRON · Memory1,890 in stockRoHS compliantDate codes 2228, 2226, 2138

MT52L256M32D1PF-107 WT:B specifications

Micron’s datasheet, “178-Ball, Single-Channel Mobile LPDDR3 SDRAM” (Rev. E, 5/2020), covers three densities: MT52L256M32D1PF (8Gb, 1 die), MT52L512M32D2PF (16Gb, 2 die) and MT52L1G32D4PG (32Gb, 4 die). This part is the single-die member. One device gives you a full 32-bit LPDDR3 interface, configured as one rank of 32 Meg x 32 x 8 banks with 32K row addresses and 1K column addresses.

Micron’s datasheet decodes the part number like this:

  • MT: Micron Technology
  • 52: Mobile LPDDR3 SDRAM
  • L: 1.2 V operating voltage (the part still needs a 1.8 V VDD1 rail)
  • 256M32: 256 Meg x 32
  • D1: LPDDR3, 1 die
  • PF: stacked FBGA package, 11 x 11.5 mm, 1 or 2 die
  • -107: cycle time 1.071 ns at read latency 14
  • WT: -30 to +85 °C
  • :B: design revision, second generation

Key specifications from the datasheet:

  • Supply rails: VDD1 1.8 V (recommended 1.70 to 1.95 V) and VDD2, VDDCA, VDDQ 1.2 V (recommended 1.14 to 1.30 V)
  • Speed: 933 MHz clock, 1866 Mb/s per pin, read latency 14, write latency 8 (set A) or 11 (set B)
  • Architecture: 8n prefetch DDR, 8 internal banks, burst length 8, multiplexed double-data-rate command/address bus
  • Operating temperature: -30 to +85 °C case temperature (TCASE)
  • Refresh: 32 ms window at TCASE up to 85 °C, 8,192 REFRESH commands, 3.9 µs average interval
  • Package: 178-ball FBGA, RoHS compliant, 11.0 x 11.5 mm, 0.85 mm maximum height, 0.8 mm x 0.65 mm ball pitch
  • Power features: per-bank refresh, temperature-compensated self refresh, partial-array self refresh, deep power-down, clock stop

The interface includes on-die termination, selectable output drive strength and a differential data strobe per byte. At 1866 Mb/s, the datasheet gives IDD0 operating current as 8 mA on VDD1, 41.5 mA on VDD2 and 6 mA on VDDCA plus VDDQ. Typical full-array self-refresh current at 25 °C is 200 µA on VDD1 and 1,100 µA on VDD2. The package is marked D9SRZ.

What end of life means for your build plan

Micron’s product change notice PCN 36228, “End of Life of Select DRAM 80s/100s, NAND 60s and NOR 60s”, lists this part with these dates:

  • Notice date: 2026-01-30
  • NCNR date (orders become non-cancelable and non-returnable): 2026-06-02
  • Last order date: 2026-08-31
  • Last ship date: 2027-09-01

Franchised distributors now list the part as obsolete.

The last order date has passed, so new orders to Micron are closed. For a product still in production, the decisions are practical:

  • Estimate remaining demand for production, service and repair through the end of your product’s life.
  • Compare that with what you hold and what the channel can still supply, and decide whether a final purchase covers the gap.
  • If it doesn’t, start qualifying a replacement now. A new DRAM on a memory-down board means firmware, layout review and validation work.
  • If you placed orders before the last order date, confirm they are scheduled to ship before 2027-09-01.

Where this LPDDR3 part is referenced

Intel validation results

Intel’s Platform Memory Operations group lists this exact part in its LPDDR3 178-ball Low Power 1866 (Memory Down) system validation results, a table dated Nov 1, 2016. Intel says the parts were tested on reference mobile platforms based on the 7th Gen Intel Core mobile U-processor line (codename Kaby Lake). A later Intel table, LPDDR3 ATE and System Validation Results, marked updated 03/05/2020, lists the part as 1866-speed, 8Gb SDP x32 for 178-ball system memory-down. Intel says the sample was tested on automated test equipment (ATE) and on Intel reference platforms. That table doesn’t name a platform for each row.

For designers, this meant a pre-tested option for soldered memory-down boards. Intel states that its testing does not replace the normal OEM component qualification process, so treat the listing as a starting point.

Microchip application note

Microchip’s application note AN2717, SAMA5D2 Dynamic Memory Implementation Guidelines, describes a test board that pairs a SAMA5D24 MPU in a 256-ball BGA with one 8Gb Micron LPDDR3 device, listed as MT52L256M32D1PF-107WT. It is a Microchip test board rather than a shipping product, but it shows the part designed in beside an embedded MPU as well as PC-class processors.

Chromebook firmware

Coreboot firmware for several Braswell Chromebook boards lists the part as a memory option. Firmware support means a board could be built with it. It doesn’t show that every unit, or any particular unit, contains it.

  • google/setzer (HP Chromebook 11 G5): the firmware lists the Micron part, by its base number without the WT:B suffix, for its 2 GiB and 4 GiB memory configurations. For those configurations it sets the device geometry by hand (x32, 8Gb, single rank), turns off automatic DRAM detection, and notes that the Micron part needs read/receive enable training before the firmware can read its MR8 register.
  • banon (Acer Chromebook 15, CB3-532), relm and terra: the same firmware family lists the part for 2 GiB configurations on banon and relm and a 4 GiB configuration on terra.

On these boards, RAM ID straps tell the firmware which memory is fitted, so one board design can take more than one memory part. These are consumer electronics designs, where a multi-source memory table keeps production moving when one part runs short.

Replacement and migration considerations for end-of-life LPDDR3

No source names a drop-in replacement. Micron’s notice gives the replacement as “Contact Sales Representative”, and no distributor lists a suggested alternative. Start with Micron directly.

The same datasheet covers two higher-density relatives, and Micron has discontinued both:

  • MT52L512M32D2PF: 16Gb, 2 die, same 11 x 11.5 mm 178-ball package. Its -107 WT:B version is on the same notice as this part, PCN 36228, with the same dates.
  • MT52L1G32D4PG: 32Gb, 4 die, larger 12 x 11.5 x 1.0 mm package. Micron’s earlier notice, PCN 35140, set a last ship date of 2024-07-31 for its -107 WT:B and -093 WT:B (1066 MHz, 2133 Mb/s per pin) versions.
  • The XT grade (-30 to +105 °C) exists in the part-number scheme. The datasheet doesn’t say whether an orderable XT version of this exact part exists.

So neither relative solves the end-of-life problem, and a different density or die count also changes what the memory controller and firmware must be told about the device. Whatever you evaluate, compare it against this checklist from the datasheet:

  • Organization: 256 Meg x 32, 8Gb, one rank, 8 banks
  • Supply rails: 1.8 V VDD1 plus 1.2 V VDD2, VDDCA and VDDQ, within the recommended ranges
  • Speed and latency: 1866 Mb/s per pin at read latency 14, or the speed your platform actually runs
  • Temperature: -30 to +85 °C TCASE at minimum
  • Footprint: 178-ball FBGA, 11.0 x 11.5 mm, 0.8 mm x 0.65 mm pitch, 0.85 mm maximum height, and the ball map in Micron’s datasheet
  • Refresh: 32 ms window, 8,192 REFRESH commands, 3.9 µs average interval
  • Firmware: SPD data, RAM ID or strap entries, and any mode-register checks (this part reports Manufacturer ID 1111 1111b in MR5 and Revision B in MR6)
  • Power: IDD0 and self-refresh currents against your battery and thermal budget

On the Chromebook boards above, each memory option has its own RAM ID entry, and the Micron part needed its own geometry and training settings. Expect firmware work on your own platform too.

Sourcing considerations

Micron ships its last orders by 2027-09-01. After that, supply is limited to stock already in the channel, much of it on the open market, which puts the verification burden on you. Obsolete LPDDR3 memory in a fine-pitch BGA is hard to inspect once it’s on a board, so check it before it gets there:

  • Full part number, including -107 and WT:B. The suffix sets speed grade, temperature range and design revision.
  • Marking code: confirm the package is marked D9SRZ.
  • Date codes and traceability back to the manufacturer or a franchised source.
  • Moisture handling: confirm dry-pack condition and moisture sensitivity handling for the BGA before reflow.
  • Country of origin documentation, where your compliance process requires it.
  • Listing accuracy: some listings describe the part as 1.2 V only, which leaves out the 1.8 V VDD1 rail.

On compatible test hardware, reading MR5 and MR6 should return Manufacturer ID 1111 1111b and Revision B. A match supports the identification, but it doesn’t authenticate a lot on its own.

Frequently asked questions

What is MT52L256M32D1PF-107 WT:B?

It is a Micron 8Gb mobile LPDDR3 SDRAM, organized as 256 Meg x 32 on a single die, in a 178-ball FBGA measuring 11.0 x 11.5 mm. The -107 grade runs at 933 MHz (1866 Mb/s per pin), and the WT grade covers -30 to +85 °C case temperature.

Is MT52L256M32D1PF-107 WT:B end of life?

Yes. Micron’s PCN 36228 lists it with a last order date of 2026-08-31 and a last ship date of 2027-09-01. Franchised distributors list it as obsolete.

What replaces MT52L256M32D1PF-107 WT:B?

No source names a replacement. Micron’s notice says to contact a sales representative. Its datasheet relatives, the 16Gb MT52L512M32D2PF and the 32Gb MT52L1G32D4PG, are also discontinued.

What supply voltages does MT52L256M32D1PF-107 WT:B need?

Two rails: VDD1 at 1.8 V (1.70 to 1.95 V recommended) and VDD2, VDDCA and VDDQ at 1.2 V (1.14 to 1.30 V recommended).

Which devices list MT52L256M32D1PF-107 WT:B?

Intel lists it in LPDDR3-1866 validation results for its Kaby Lake reference platforms, and Microchip’s AN2717 application note uses it on a SAMA5D24 test board. Coreboot firmware lists it as a memory option for several Braswell Chromebook boards, including setzer (HP Chromebook 11 G5), banon, relm and terra. That shows firmware support, not that every unit contains it.

What is the marking code for MT52L256M32D1PF-107 WT:B?

The FBGA marking code is D9SRZ.

From the catalog

More memory and MICRON parts at NetSource

Browse the parts we list, with date codes and RoHS status on each part page.

Not listed?

We source it

We source end-of-life and hard-to-find parts too. Send the part number and we'll quote it.

Request a quote

Any part number, in stock or not